Torque Specs For Pontiac G6

I will add more items as questions and requests arise. Tie Rod Retention Nut.

Pontiac G6 Gt

Oil Pan to Block.

Torque specs for pontiac g6. Torque Specifications for GM 38L-231ci-V6. Tighten the bolts in a circular motiongoing around the pan in a clockwise motion. Engine horsepower torque dimensions and mechanical details for the 2007 Pontiac G6.

Tighten to 50 Nm 37 lb ft 40 degrees. Pontiac lug nut torque specs Pontiac lug nut torque specs Here are Pontiac lug nut torque specs. TightenTighten the oil pan bolts to 12 Nm 9 lb ft.

Clean the transaxle case and oil pan gasket surfaces with solvent and allow to air dry. Hello here is the torque spec for front hub bearing. Connecting rod bolts 40-45 ft-lbs.

Oil Pump to Block. 27 rows Torque to. Flywheel flex-plate bolts 75-85 ft-lbs.

If you need a torque specification not listed please send me a message and I will find the proper specification using the service manual. For 289 HP Boss 302 Cylinder head bolts 65-72 ft-lbs. Below you will find a list of common torque specs for the 2004-2006 Pontiac GTO.

Tighten the front bushing to frame bolt to 50 Nm 37 lb ft plus 90 degrees. Rear Main Cap to Block. All 2001-02 100 ft-lbs Aztek 2003-05 100 ft-lbs Bonneville 2003-05 100 ft-lbs G3 2009-10 88 ft-lbs G5 2007-09 100 ft-lbs G6 2005-10 100 ft-lbs G8 2008-09 125 ft-lbs Grand Am 2003-05 100 ft-lbs Grand Prix 2003-08 100 ft-lbs GTO 2004-06 100 ft-lbs.

Poor Gas Mileage- If the converter is not locking at speed the engines RPMs will stay higher. 2007 Pontiac wave torque settings for wheel bearing replacement If it is the drive axle hub nut you are reffering to the torque spec is 221 ft lbs Read full answer. 95 lbft NOTE 1.

Pontiac Bolt Settings Chart Make Model Trim Year Range Torque PONTIAC 6000 24 DOOR ALL5-115 1984 - 1991 100 ft-lbs AZTEK 15-INCH AWD 2001 - 2005 100 ft-lbs BONNEVILLE 14. 260 289 302 Torque Spec. Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs.

Reverse the nut 34 of a turn. Tighten the ball stud to steering knuckle pinch nut to 50 Nm 37 lb ft. If the converter stays unlocked it can be a nuisance.

Cam bolts 40-45 ft-lbs. The lug nut torque spec - 140ftlbs caliper mount - 80ftlbs caliper bracket 129ftlbs axle nut 177ftlbs. Before you install your wheels check your vehicles recommended torque.

2007 Pontiac G6 technical specifications and data. Front transmission mount rear transmission mount center transmission mount and motor mount. Harmonic damper bolts 70-90 ft-lbs.

Cam thrust plate bolts 8-10 ft-lbs. This decreases fuel mileage. Install the oil pan gasket the oil pan and hand start the oil pan bolts.

The symptoms of P0740 vary greatly. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. 64 rows PONTIAC TORQUEENGINE SPECIFICATIONS.

32 rows Torque Specs Application. Tighten the nuts and the bolts with the front suspension loaded by using the proper jackstand. Rocker arms 17-23 ft-lbs.

Balance Shaft Sprocket To Balance Shaft. Pressure plate bolts 35 ft-lbs. Main Caps 1-4 to Block.

Pontiac Deck Height. I need to know if my car is a 4 speed or 6 speed. Tighten to 8 ft-lbs 10 N-m then tighten an additional 13 turn to at least 37 ft-lbs 50 N-M.

Upon initial installation of replacement ball joint tighten nut to to 81 ft-lbs 110 N-m. What are the torque specs for a Pontiac g6 35 2007 of the following. The most common symptoms include.

Cylinder Head to Block with Grease Under Head of Bolt Bolt. Strut to Steering Knuckle Bolt and Nut. Control arm torque specification for a 2005 Pontiac g6 Go to this URL.

If it locks when it shouldnt be thats where it can get dicey.

2006 Pontiac G6 Specs And Prices